Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment



Removal, capital repairs and installation of the lower levers of a forward suspension bracket

Forward suspension bracket

1 — the Cross beam
2 — the Bolt (25 Nanometers)
3 — the Bracket
4 — the Rubber plug
5 — a bolt
6 — the Holder with the rubber-metal plug
7 — Samokontryashchayasya a nut (100 Nanometers)
8 — the Back pillow of the cross lever
9 — M6 Bolt (7 Nanometers)
10 — the Bolt (70 Nanometers)
11 — the Washer
12 — the Cross lever of a suspension bracket

13 — Bolts
14 — the Spherical support
15 — the Nut (25 Nanometers)
16 — the Forward pillow of the cross lever
17 — Samokontryashchayasya a nut (90 Nanometers)
18 — the Bolt
19 — the Bolt
20 — the Arm of fastening of a jet bar with a rubber pillow
21 — the Washer
22 — Samokontryashchayasya a nut (5 Nanometers)
23 — the Bolt (45 Nanometers)
24 — the Washer


At assembly the new nut of a coupling bolt of a tent support and also a new nut of a forward axial bolt will be required. Also prepare new spring washers of bolts of fastening of the lever.

REMOVAL

 PERFORMANCE ORDER

1. Prop up wedges back wheels, cock the parking brake, then a front of the car and establish to a poddomkratta it on props. Remove the corresponding forward wheel.
2. On the models equipped with the stabilizer of cross stability give a nut of fastening of a rack of a bar of the stabilizer to the lower lever, remove a washer and the lower rubber insert. Components of fastening of the lower lever of a suspension bracket are presented on an illustration.

3. On all models give a nut and take a coupling bolt of a collar of fastening of stupichny assembly to the lower lever...

... by means of mount carefully lower the lower lever, releasing a spherical support from the landing collar in the basis of stupichny assembly. On the models equipped with the stabilizer of cross stability try not to allow losses of a rubber pillow and a washer of the top support of a rack of a bar of the stabilizer.

The nut of a coupling bolt of a spherical support is subject to replacement without fail.

4. Give a nut of a forward axial bolt of the lower lever, remove a washer.

At assembly the nut is subject to replacement without fail.

5. Give a nut and bolts of fastening of the back axial plug of the lower lever to the car bottom...

... remove spring washers from bolts - at assembly they are subject to replacement without fail.

On some models the nut of fastening of the plug can be replaced with a rivet.

6. Take out master a bolt from the plug of a forward support and take assembly of the lever from under the car.


Capital repairs


 PERFORMANCE ORDER

1. Carefully wipe the lever and landing surfaces of its support, having removed from them all traces of dirt and an anticorrosive covering of the bottom. Attentively examine assembly on existence of cracks, deformations and other mechanical damages. Pay special attention to a condition of axial plugs. Replace defective components.
2. Replacement of axial plugs requires a hydraulic press, a stripper of bearings and several remote plugs. In view of told, performance of this work will be more correct to be charged to the specialists of car service having everything the necessary equipment. The order of holding a procedure is described below.
3. For replacement of the forward plug first of all try to remember its correct adjusting situation. Then reliably prop up the lever and squeeze out of it the plug. Carefully wipe nest walls under landing of the plug. Before installation of the new plug moisten it with soap solution.

4. The back plug also has to be installed strictly definitely an obligatory order to the relation to the lever. Otherwise in use the car the plug will be exposed to excessive loadings. Squeeze out assembly of the lever of an arm, then squeeze out the plug of the end of the lever. Carefully wipe nest walls under landing of the plug. Before installation of the new plug moisten it with soap solution. At assembly track that the plug correctly was deployed by the groove concerning the lever.

INSTALLATION

 PERFORMANCE ORDER

1. Start the lower lever of a suspension bracket on the regular place and fill a shaft of a spherical support in a collar in the basis of stupichny assembly. On the models equipped with the stabilizer of cross stability arrange a stabilizer bar rack on the lever, having tracked correctness of landing of a rubber insert and washer of the top support.
2. Insert a forward axial bolt, establish a washer, screw a new nut and tighten it, so far only by hand.
3. Screw a fixing nut (at the corresponding complete set) an arm of the back axial plug. Screw bolts (do not forget to replace spring washers). Tighten bolts with the required effort, then tighten a nut. At the corresponding complete set instead of a nut establish a new rivet.
4. Make sure of correctness of landing of a coupling bolt in stupichny assembly. Screw a new nut and tighten it with the required effort.
5. Where it is required, establish a rubber insert and a washer of the lower support of a rack of a bar of the stabilizer, screw a nut and tighten it with the required effort.
6. Establish into place a wheel, then lower the car on the earth and with the required effort tighten wheel bolts.
7. Shake the car for shrinkage of components of the lever, then tighten a nut of a forward axial bolt with the required effort.