Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment





Removal and installation of a forward stretcher

At assembly new nuts of racks of the stabilizer of cross stability, and also a nut of spherical fingers will be necessary.

REMOVAL

 PERFORMANCE ORDER

1. Prop up wedges back wheels, firmly cock the parking brake, then a front of the car and establish to a poddomkratta it on props. Remove both forward wheels.
2. Remove a reception pipe and the catalytic converter of system of production of the fulfilled gases (see the Part Dismantle of the power unit and capital repairs of the engine of the Head Remont of the engine).
3. Remove the stabilizer of cross stability (see the Section Removal and installation of the stabilizer of cross stability of a forward suspension bracket).
4. Remove both lower levers of a suspension bracket (see the Section Removal, capital repairs and installation of the lower levers of a forward suspension bracket).
5. Turn out coupling bolts of collars of support of a case of the steering mechanism. Remove collars from a stretcher.
6. Give a nut and take a through bolt of fastening of a back support of a suspension bracket of the power unit.
7. Track that all cables and hoses fixed on a stretcher were released from clamps and are taken aside.
8. Get under a stretcher a jack with the wooden whetstone laid on its head.
9. Turn out bolts of fastening of a stretcher, accurately omit assembly on a jack and take it from under the car. Track that in the course of extraction the stretcher did not cling to tubes of lines of system of hydrostrengthening of a wheel.

INSTALLATION

 PERFORMANCE ORDER

Installation is made upside-down. Special attention should be paid to the next moments:

a) Fixing bolts have to be tightened strictly with the required effort;
b) Before installation of collars track correctness of placement of rubber pillows of support of the steering mechanism (plugs have to nestle on a stretcher the flat party). Smooth out a carving of fixing bolts, then grease with the fixing sealant like Loctite 270. You make tightening of bolts with the required effort;
c) You make installation of the lower levers and the stabilizer of cross stability according to the instructions provided in the Sections Removal, capital repairs and installation of the lower levers of a forward suspension bracket, Removal and installation of the stabilizer of cross stability of a forward suspension bracket;
d) The order of installation of system of production of the fulfilled gases is given in the Part Dismantle of the power unit and capital repairs of the engine of the Head Remont of the engine;
e) In conclusion do not forget to check geometry of a forward suspension bracket (see the Section the Angles of installation of wheels of the car - the general information).