Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment





Replacement of bearings of back naves

Stupichny assembly of a back wheel

1 — the Cover
2 — a bridge Pin
3 — the Brake drum
4 — the Nave
5 — the Bearing
6 — the Epiploon

7 — the Bolt of fastening of a pin to the lever
8 — the Bearing
9 — the Washer
10 — the Nut
11 — Koronchataya a lock washer
12 — the Forelock


 PERFORMANCE ORDER

1. Remove the brake drum (see the Head the Brake system).

2. Having hooked the screw-driver with a flat sting, take an epiploon from assembly of the brake drum - try to remember how it was established.

3. Take the internal bearing from a drum.

4. Prop up assembly and beat out from it a holder of the external bearing.

5. Turn a drum and beat out a holder of the internal bearing.

6. Carefully smooth out a landing nest in a drum, having completely removed all traces of dirt and old lubricant. Teases, agnails and roughnesses remove by means of a fine-grained emery paper. Attentively check a surface for existence of cracks and other signs of wear. In case of need make replacement of a component. Replacement of bearings and an epiploon is made without fail, regardless of their state as at dismantle external holders inevitably collapse. Prepare new bearings, an epiploon and special universal lubricant.
7. Before installation slightly oil external holders of bearings pure motive for the purpose of landing simplification.
8. Having reliably propped up a drum, put an external holder of the external bearing on the place. Densely begin to knock a holder in a reception nest, having tracked perpendicularity of its landing. As a mandrel use a piece of a pipe of suitable diameter - the mandrel has to rest only against the outer edge of a holder.
9. Turn a drum and, working in the same order, establish in it an external holder of the internal bearing.
10. Make sure of correctness of landing of both external holders, then carefully wipe assembly.

11. Fill lubricant both conical roller bearings, also apply lubricant on their external holders.

12. Put the internal bearing in the external holder.

13. Fill a new epiploon with sponges inside in a reception nest from the back party of a drum.

14. Put an epiploon aflush with the surface of the reel, or against the stop in a back part of the last. In case of need the epiploon can be begun to knock in a nest by means of the mandrel made of a piece of a pipe of suitable diameter. Remember that the mandrel has to rest only against the firm outer edge of an epiploon.

15. Turn a drum and put the external conical roller bearing in the external holder. Establish a gear washer.
16. Fill hug bearings lubricant and establish into place assembly of the brake drum (see the Head the Brake system).