Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment





Removal and installation of external tips of steering drafts

Implementation of this procedure requires a stripper of spherical support.

REMOVAL

 PERFORMANCE ORDER

1. Cock the parking brake, then a front of the car and establish to a poddomkratta it on props. Remove the corresponding forward wheel.
2. If the tip does not need replacement and will be used further, use the measuring instrument of planeness and mark with a chertilka its situation on draft.
3. Having recorded a draft bar, on a quarter of a turn weaken a lock-nut of fastening of a tip. Leave a nut in this situation in quality of a reference point at assembly.

4. Take the forelock and give a nut of fastening of an external tip of draft. Release the tip hinge from the rotary lever of stupichny assembly - in case of need use a stripper.

5. Screw together a tip from a bar of steering draft - count quantity of turns and try not to shift a lock-nut.
6. In case of need count quantity of rounds of a carving from a bar end face to a lock-nut. Write down result. Now the nut can be also removed.
7. Carefully clear a tip and a carving part of draft. If the hinge is stirred up or, on the contrary, soured, the tip should be replaced. Carefully check a condition of a conical shaft and a carving part of a spherical finger. In case of need in an individual order replace the damaged cover of the spherical hinge. Make sure that the hinge is filled by lubricant. In case of need add necessary amount of lubricant like Milykote Longterm 2/78, then establish a new cover and fix it by bandages.

INSTALLATION

 PERFORMANCE ORDER

1. If it is required, screw a lock-nut (in former situation - be verified by quantity of rounds of a carving) on a draft bar.
2. Screw a tip on a draft bar on former quantity of turns (at the same time a lock-nut have to it is separated from a tip end face exactly on a quarter of a turn - achieve combination of the tags put in the course of dismantle).
3. Fill the draft tip hinge in the rotary lever of stupichny assembly and screw a fixing nut. Strongly tighten a nut and record it the new forelock.
4. Establish into place a wheel, then lower the car on the earth and tighten wheel bolts with the required effort.
5. Check the angles of installation of forward wheels, in case of need make the corresponding adjustment (see the Section the Angles of installation of wheels of the car - the general information). Now tighten a lock-nut of a tip of steering draft with the required effort.