Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment





Removal, capital repairs and installation of pins of the back bridge

REMOVAL

 PERFORMANCE ORDER

1. Prop up wedges forward wheels, then a back of the car and establish to a poddomkratta it on props. Remove the corresponding back wheel.
2. Remove the brake drum (see the Head the Brake system). On the models equipped with ABS, an otboltita and the wheel sensor and, without disconnecting an electrical wiring, remove it from stupichny assembly aside.
3. For the purpose of minimization of losses of brake fluid uncover the GTTs tank, enclose under it a polyethylene film and again densely screw, having achieved the required sealing. Alternatively, press a clamp a flexible brake hose as it is possible closer to the wheel cylinder.
4. Wipe outside nipple connection of a brake tube, give a cap nut and accurately separate a tube from the wheel cylinder. At once to a zakuporta the open ends of a tube and the union in order to avoid hit in system of dirt. Collect by rags traces of the spilled liquid.
5. Turn out bolts of fastening of assembly of a brake board and separate the last from a pin of the back bridge. Remove assembly of a pin of the bridge from the car. temporarily fix a brake board on the bridge by couple of bolts in order to avoid a pulling of a driving cable of the parking brake.
6. Check assembly of a pin for existence of mechanical damages, zadir and agnails. In case of need make replacement.

Do not make attempts of correction of the bent pin at all.

INSTALLATION

 PERFORMANCE ORDER

1. Carefully smooth out the interfaced surfaces of the bridge, assembly of pins and a brake board. Check a condition of a board, in case of need remove the revealed roughnesses by means of a file or a fine-grained emery paper.
2. Start assembly of a pin with a brake board on the regular place, screw fixing bolts and in a diagonal order tighten them with the required effort.
3. Wipe a brake tube and connect it to a back part of the wheel cylinder. Strongly tighten a cap nipple nut.
4. Remove the clamp pressing a brake hose / take a polyethylene film from under a GTTs tank cover, then install into place the brake drum and pump over a hydraulic contour (see the Head the Brake system). On the models equipped with ABS install into place the wheel sensor.