Skoda Felicia

1. Track reliability of fastening of the electric socket. When landing assembly to the regular place try not to allow a latching of wires.
2. Screw fixing screws and tighten them with the required effort.
3. Make sure that in the car there is nobody, then connect the battery. Through an open driver's door include ignition and make sure of serviceability of operation of a control lamp.

1. Accurately release clamps and uncover access to assembly to a pillow the passenger party of the dashboard.
2. Give nuts of fastening of assembly of a safety cushion and remove washers. Accurately remove assembly from the seat and disconnect from it an electrical wiring.
3. For removal of a basic arm of assembly turn out screws of fastening of an arm of the panel of finishing (through a cover panel opening), then release the panel basis from clamps and remove section from the dashboard. Give fixing nuts, throw off washers and remove a basic arm from a partition of a motive compartment.

1. If removed, establish into place a basic arm on a partition of a motive compartment and tighten nuts of its fastening with the required effort. Latch into place the panel of finishing and strongly tighten screws of its fastening.
2. Connect an electrical wiring, having tracked reliability of fixing of the socket and put assembly of a pillow on the regular place, - try not to clamp wires. Screw fixing nuts and tighten them with the required effort. Install a cover of access to assembly of a safety cushion on the dashboard.
3. Make sure that in the car there is nobody, then connect the battery. Through an open driver's door include ignition and make sure of serviceability of operation of a control lamp.

1. Remove the central console (see the Section Removal and installation of the central console).
2. Remove the radio tape recorder (see the Section Removal and installation of the autoradio tape recorder), then unbend lock uvulas and take an assembly sled from the nest in the dashboard. Disconnect the antenna of the roller bearing and an electrical wiring of food from a sled.
3. Remove the sleeve connecting the heater casing basis to an air duct of a back foot well.

4. Give fixing nuts and remove the foot emphasis established near a coupling pedal.

5. On models with right-hand steering in a passenger foot well release a clamp and remove a decorative cover from the left arm of a support of pedal assembly.

For an otpuskaniye of a clamp take from it the central pin.

6. On all models unbend a carpet for the purpose of ensuring access to located under the forward end of a foot air duct of the control unit of a safety cushion.

7. Give fixing nuts, throw off washers and remove the control unit from the support.

8. Release a clamp, disconnect an electrical wiring and take the control unit from the car.

1. Connect an electrical wiring and strongly latch a socket clamp. Install the control unit on the support (the arrow has to indicate more true planes of the block on the car forward). Screw fixing nuts and tighten them with the required effort.
2. Establish into place an air sleeve, having tracked correctness of introduction it in gearing with reciprocal components.
3. Unbend a carpet and establish into place a foot emphasis, having strongly tightened its fixing nuts.
4. On models with right-hand steering establish a decorative cover on the left arm of pedal assembly and reliably fix it by a clamp.
5. On all models install the central console (see the Section Removal and installation of the central console).
6. Connect an electrical wiring and an antenna cable to a radio tape recorder sled. Fill a sled in the dashboard, having tracked reliability of fixing it lock uvulas. Install into place the radio tape recorder.
7. Make sure that in the car there is nobody, then connect the battery. Through an open driver's door include ignition and make sure of serviceability of operation of a control lamp.

1. Remove assembly of a driver's safety cushion, then remove a steering wheel.

2. Mark position of the contact block in relation to a steering wheel, then turn out fixing screws and divide components. Do not rotate the contact block removed from the car!

1. Install the contact block on a steering wheel of the car according to the landing tags put in the course of dismantle. Screw and strongly tighten fixing screws. At installation of the new block cut off and remove a fixing collar.
2. Establish into place a steering wheel (see the Section Removal and installation of a steering wheel), then establish assembly of a driver's safety cushion.

Performing procedures of removal and installation of assemblies of side safety cushions should be charged to specialists of car service, in view of big risk of damage of an upholstery of seats.