Skoda Felicia

since 1994 release

Repair and operation of the car

Removal and installation of assemblies of external lighting and alarm fixtures

Before getting to work do not forget to disconnect a negative wire from the battery (see the prevention provided in the Section the General information and precautionary measures).

Head headlights

PERFORMANCE ORDER

1. Remove both forward indexes of turn.
2. On release models till 1998 turn out the left and right bolts of fastening of the panel of a front (access to bolts opens through openings under installation of indexes of turns). Also turn out two screws of fastening of the top part of the panel to a cross beam of the lock of a cowl. Give fixing nuts in a back part of the panel, then remove the last from the car.

3. On release models since 1998 turn out the fixing screw, then remove the decorative cover established between a head block headlight and a front bumper.

4. On all models turn out the top and lower screws of fastening of a head block headlight.

5. Take a block headlight from the nest and disconnect an electrical wiring.

6. Having turned assembly of the regulator of the direction of an optical axis, disconnect it from a back part of a block headlight, then finally remove a headlight.

7. In case of need accurately release fixing clamps and remove a lens from a block headlight. Remove a sealant from a block headlight, check its state, in case of need replace.

8. Installation is made upside-down. All fixture has to be tightened with the required effort. Track reliability of a zashchelkivaniye of clamps and connections of the regulator. In conclusion it is necessary to check installation of an optical axis of a headlight (see the Section Adjustment of the Direction of an Optical Axis of Head Headlights - the general information and replacement of the mechanism of the regulator).

Assemblies of forward indexes of turns

PERFORMANCE ORDER

1. Find a clamp of fastening of assembly of the index in a forward corner of a motive compartment of the car. Wring out a lock uvula and release assembly of the index from a car wing.

2. Turn and take a cartridge with the index lamp established in it. In case of need for simplification of access to the index remove from the support an air cleaner casing (see the corresponding Part of the Head the Power supply system).

3. Installation is made upside-down. Track reliability of a zashchelkivaniye of a clamp of assembly.

Forward fog lights

PERFORMANCE ORDER

Information given below belongs only to release models till 1998. Fresher data at the time of drawing up the present manual were absent.

1. Having hooked the small screw-driver with a flat sting, accurately remove facing of a fog light from a front bumper of the car.
2. Turn out fixing screws and take a headlight from the landing nest in a car bumper. Disconnect an electrical wiring and remove a headlight from the car.
3. Installation is made upside-down. In case of need rotation of the adjusting screw correct the provision of an optical axis of a headlight.

Side repeaters of forward indexes of turns

PERFORMANCE ORDER

1. Through an arch of a wheel push out assembly of the repeater from a car wing.

2. Release a cartridge and remove a lens.

3. Installation is made upside-down. Track reliability of fixing of a lens of the repeater.

Assemblies of the back combined lamps

PERFORMANCE ORDER

1. Release clamps and remove assembly of a lamp holder from a back part of a lamp.

2. Give fixing nuts and remove assembly of a lamp from the car (together with a sealant) (see an accompanying illustration). Check a condition of a sealant, in case of need make replacement.

3. Installation is made upside-down. Track correctness of landing of a sealant.

Stoplight of the top level

PERFORMANCE ORDER

1. Turn out fixing screws and separate assembly of a stoplight from an internal wall of a door of a back.

2. Disconnect an electrical wiring and remove assembly from the car.

3. Installation is made upside-down.

Lamp of illumination of back registration plate

PERFORMANCE ORDER

1. Having accurately hooked the small screw-driver with a flat sting, release assembly from a back door.
2. Take a cartridge and remove a lens.
3. Installation is made upside-down. Track reliability of fixing of a lens.