Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and finishing of salon
- Onboard electric equipment
   General information and precautionary measures
   Search of causes of failures of electric equipment
   Safety locks, the relay and breakers - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm fixtures
   Replacement of lamps of internal lighting fixtures
   Removal and installation of assemblies of external lighting and alarm fixtures
   Adjustment of the direction of an optical axis of head headlights - the general information and replacement of the mechanism of the regulator
   Removal and installation of an instrument guard
   Removal and installation of a cable of the drive of a speedometer
   Removal and installation of the lighter
   Removal and installation of a horn of a horn
   Removal and installation of levers of screen wipers
   Removal and installation of an electric motor and drafts of the drive of screenwashes
   Removal and installation of an electric motor of the drive of a cleaner of back glass
   Removal and installation of components of washers of wind glass / lenses of head headlights / back glass
   Removal and installation of the autoradio tape recorder
   Removal and installation of loudspeakers
   Removal and installation of the antenna of the radio receiver
   Anticreeping alarm system / system of an immobilization of the engine
   Removal and installation of components of a heating system of front seats
   Safety cushion - the general information, precautionary measures and deactivation of system
   Removal and installation of components of system of safety cushions
   Diagnostics of electronic control systems of the engine and systems of safety
   + Schemes of electric connections



Removal and installation of an electric motor and drafts of the drive of screenwashes

REMOVAL

 PERFORMANCE ORDER

Include screen wipers and stop them in parking situation. Disconnect a negative wire from the battery. (see the prevention in the Section the General information and precautionary measures).


Driving electric motor

 PERFORMANCE ORDER

1. Disconnect an electrical wiring from the driving motor.

2. Give a nut of fastening of a crank of driving draft, remove a washer, then disconnect a crank from an electric motor spindle.

3. Turn out fixing bolts and remove assembly of an electric motor from the car.

Assembly of an electric motor with driving drafts .

 PERFORMANCE ORDER

5. Remove levers of screen wipers (see the Section Removal and installation of levers of screen wipers).
6. Disconnect an electrical wiring from the driving motor.
7. Give a plastic nut and release clamps of fastening of the panel of a fairing. Separate the fairing panel from the basis of a windshield and take him aside from drafts of the drive of screen wipers.

8. Remove protective caps from spindles of fastening of both levers, then give nuts and remove flat and sealing washers.

9. Remove assembly of the drive from the regular place and remove from the car, remembering adjusting situation on support of different assembly of washers and remote plugs.

On models with left-side steering, perhaps, it is necessary to release clamps and to remove the top section of a casing of a heater for the purpose of providing sufficient working space.

INSTALLATION

Driving electric motor

 PERFORMANCE ORDER

1. At installation of the new motor previously connect it to an electrical wiring, or directly to the battery for the purpose of reduction in parking situation.
2. Start the motor on the regular place and strongly tighten fixing bolts.
3. Make sure of correctness of position of levers of both screen wipers (they have to be in parking situation), then put on a crank of driving draft a motor spindle. Establish a washer, then screw a fixing nut and tighten it with the required effort.
4. Connect an electrical wiring to the motor, then connect the battery.


Assembly of an electric motor with driving drafts

 PERFORMANCE ORDER

Installation is made as it should be, the return to a dismantle order. Track correctness of placement of washers and remote plugs. Tighten with the required effort of a nut of fastening of levers.