Skoda Felicia

since 1994 release

Repair and operation of the car

Replacement of lamps of external lighting and alarm fixtures

General information

At failure of any glow lamps, it is necessary to pay attention to the next moments:

a) Before starting replacement, disconnect a negative wire from the battery (see the remark provided in the Section the General information and precautionary measures);
b) Remember that just burning lamp during even some time remains very hot;
c) Try not to touch a flask of lamps with naked fingers and not to leave on it the fat spots causing decrease in brightness of a luminescence and to gradual tarnishing of a reflector;
d) Check quality of electric contact between a socle of a lamp and plugs of her boss. Before installation of a new lamp smooth out plugs from corrosion traces. In lamps of bayonetny type you watch that contacts of the boss densely nestled on socle plugs;
e) You watch that the replaceable lamp corresponded according to the electric characteristics failed.

Head headlights

PERFORMANCE ORDER

1. Turn an access cover counterclockwise and remove it from a back part of a head block headlight.

2. Disconnect an electrical wiring from a lamp.

3. Release clamps and take a lamp with the boss from a back part of a block headlight. Take a lamp from the boss.

4. Try not to touch a flask of a new lamp with naked fingers - use a paper towel or a napkin. Delete incidentally left spots by rubbing of a flask with methyl alcohol.
5. Establish a new lamp, having tracked correctness of landing of assembly in a block headlight.
6. Connect an electrical wiring and establish an access cover (a tag of "TORAHS" up).

Forward marker lights

PERFORMANCE ORDER

1. Turn an access cover counterclockwise and remove it from a back part of a head block headlight.
2. Take a cartridge of a lamp of a marker light from a block headlight, then take a lamp from the boss.

3. Installation is made upside-down. Track that the cover of access was the tag of "TORAHS" established on a block headlight up.

Forward fog lights

PERFORMANCE ORDER

Information given below is related only to release models till 1998. At the time of drawing up the present manual information on later models was absent.

1. Having accurately hooked the small screw-driver, remove facing of a fog light from the forward party of a bumper.
2. Turn out fixing screws and release assembly of a headlight from a bumper. Disconnect an electrical wiring and remove a headlight from the car.
3. Release a fixing clamp and take a lamp from a headlight.
4. Try not to touch a flask of a new lamp with naked fingers - use a paper towel or a napkin. Delete incidentally left spots by rubbing of a flask with methyl alcohol.
5. Establish a new lamp, having tracked correctness of landing of a reflector and reliability of fixing of assembly.
6. Connect an electrical wiring, then establish assembly of a headlight in a front bumper. Strongly tighten fixing screws. Then install into place the facing panel.

Forward indexes of turns

PERFORMANCE ORDER

1. Find a clamp of fastening of the index of turn in a forward corner of a motive compartment. Release a clamp and release assembly of the index from a wing. For ensuring access to the index of the right turn there can be a need for removal from the support of a casing of the air cleaner (see the corresponding Part of the Head the Power supply system).

2. Turn a cartridge of a lamp counterclockwise and take it from assembly of the index.

3. The socle of a lamp has a bayonetny design therefore for extraction the lamp should be pressed down and to turn slightly counterclockwise.

4. Installation is made upside-down. Track reliability of fixing of assembly of the index in a car wing.

Side repeaters of forward indexes of turns

PERFORMANCE ORDER

1. Having reached through a wheel arch, push out assembly of the repeater from a wing.
2. Release a cartridge from assembly of a lens, then take a lamp.

3. Installation is made upside-down. Track reliability of fixing of a lens in a car wing.

Assembly of the back combined lamp

PERFORMANCE ORDER

1. In the luggage compartment of the car release clamps and remove assembly of a lamp holder from a lamp.

2. All lamps are equipped with socles of bayonetny type and for extraction have to be slightly drowned and turned counterclockwise.

Pay attention that contact probes of a lamp of a stoplight / a back marker light are located asymmetrically that defines unambiguity of landing of a lamp in the holder.

3. Installation is made upside-down. Track reliability of fixing of assembly of a lamp holder.

Stoplight of the top level

PERFORMANCE ORDER

1. Release clamps and remove assembly of a lamp holder from the back party of a lamp.

2. Take the lamp which is subject to replacement from the holder. All lamps are equipped with socles of press type.

3. Installation is made upside-down. Track reliability of fixing of a lamp holder in a lamp.

Lamp of illumination of registration plate - the Sedan and Hatchback model

PERFORMANCE ORDER

1. Having accurately hooked the small screw-driver, release assembly of a lamp from a back door.

2. Release a cartridge of a lamp from a lamp lens, then take the lamp equipped with a socle of press type from the boss.

3. Installation is made upside-down. Track reliability of fixing of a lens at back doors.