Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and finishing of salon
- Onboard electric equipment
   General information and precautionary measures
   Search of causes of failures of electric equipment
   Safety locks, the relay and breakers - the general information
   Removal and installation of switches
   Replacement of lamps of external lighting and alarm fixtures
   Replacement of lamps of internal lighting fixtures
   Removal and installation of assemblies of external lighting and alarm fixtures
   Adjustment of the direction of an optical axis of head headlights - the general information and replacement of the mechanism of the regulator
   Removal and installation of an instrument guard
   Removal and installation of a cable of the drive of a speedometer
   Removal and installation of the lighter
   Removal and installation of a horn of a horn
   Removal and installation of levers of screen wipers
   Removal and installation of an electric motor and drafts of the drive of screenwashes
   Removal and installation of an electric motor of the drive of a cleaner of back glass
   Removal and installation of components of washers of wind glass / lenses of head headlights / back glass
   Removal and installation of the autoradio tape recorder
   Removal and installation of loudspeakers
   Removal and installation of the antenna of the radio receiver
   Anticreeping alarm system / system of an immobilization of the engine
   Removal and installation of components of a heating system of front seats
   Safety cushion - the general information, precautionary measures and deactivation of system
   Removal and installation of components of system of safety cushions
   Diagnostics of electronic control systems of the engine and systems of safety
   + Schemes of electric connections



Removal and installation of switches

Before starting performing procedures disconnect a negative wire from the battery (see the remark provided in the Section the General information and precautionary measures).


Switch ignition/lock of blocking of a steering column

See the Head Podvesk and steering.

The combined understeering switches

General information


The combined understeering switch consists of two separate knots fixed on a steering column of the car.

The electrical wiring plait which is coming to an end with the 8-contact socket is brought out of assembly of the switch.

The switch of indexes of turns is equipped with the mechanical returnable device providing automatic shutdown of the alarm system upon return of a steering wheel in rectilinear situation. The electrical wiring plait which is coming to an end with the 9-contact socket is brought out of the switch.

REMOVAL AND INSTALLATION

 PERFORMANCE ORDER

1. Remove a steering wheel (see the Head Podvesk and steering).
2. On models without driver's safety cushion turn out the fixing screw and lower the lower casing of a column, releasing it from clamps. Remove a casing from a column.
3. On all models turn out the fixing screw, release clamps and remove assembly of the top casing from the panel of devices/holder of switches.

4. Now each of switches can be removed from the holder in an individual order after an otpuskaniye of the corresponding fixing clamps.

5. Having released the switch of their holder, disconnect from it an electrical wiring.

6. Installation is made upside-down. Track reliability of subjoining of the electric socket and correctness of an arrangement of contacts of a horn. Having made sure that everything is all right, establish into place casings.


Press switches of the dashboard

 PERFORMANCE ORDER

1. Remove an instrument guard (see the Section Removal and installation of an instrument guard).

2. Assembly of each of switches can be taken from a guard casing in an individual order by an otpuskaniye of the corresponding clamps.

3. At installation track reliability of a zashchelkivaniye of clamps of the switch. The description of the procedure of installation of an instrument guard is provided in the Section Removal and installation of an instrument guard.


Switch of management of functioning of the electric drive of external rear-view mirrors

 PERFORMANCE ORDER

1. Lift the internal handle of a door, then accurately hook and remove the panel of its finishing.
2. Release the switch from clamps in assembly of the handle and disconnect from it an electrical wiring.
3. Installation is made upside-down.

Assembly of switches of management of functioning of window regulators/heating of front seats

 PERFORMANCE ORDER

1. Trying not to damage an overlay of the console, hook assembly of switches the small screw-driver and take it from the landing nest.
2. Disconnect an electrical wiring and take assembly from the car.
3. Installation is made upside-down.


Door switches of illumination of salon

 PERFORMANCE ORDER

1. Open a door and remove a rubber protective cover from assembly of the switch.

2. Release clamps and, having accurately hooked, take the switch from a door pillar. Disconnect an electrical wiring (see an accompanying illustration). Glue the sticking-out piece of an electrical wiring with the socket plug an adhesive tape that it incidentally did not fail in a rack.

If insufficiency of a weak point of an electrical wiring does not allow to make removal of the switch, remove from a rack of the panel of internal finishing, having provided thereby access to the socket in the last.

3. Installation is made upside-down. Track reliability of landing of a rubber protective cover.

Switch of lighting of the luggage compartment

 PERFORMANCE ORDER

1. Remove assembly of the lock of a door of a back (see the Head Kuzov and finishing of salon).
2. Disunite the electric socket and take from castle assembly the switch of illumination of salon /

3. Installation is made upside-down. Before establishing an insulating film and the panel of internal finishing on a door make sure of serviceability of functioning of the switch.


Sensor switch of stoplights

See the Head Brake system.

Sensor switch of the lever of the parking brake


 PERFORMANCE ORDER

1. On appropriately equipped models remove the central console (see the Head Kuzov and finishing of salon).
2. On models without the central console hook and remove a decorative cover from the lever of the parking brake.

3. Turn out the fixing screw and remove a decorative cover of the sensor switch.

4. Take the sensor switch from the landing nest and disconnect from it an electrical wiring.

5. Installation is made upside-down. Before installing into place the central console / cover of the lever, check serviceability of functioning of the sensor switch.


Switch of the choice of the high-speed modes of the fan of a heater

 PERFORMANCE ORDER

1. Remove assembly of a casing of the heater/fan (see the Head of the Cooling system, heating).

2. Disconnect an electrical wiring from assembly of the switch.

3. Remembering the adjusting provision of all components (tips of cables are marked with a color code), by means of nippers release clamps and disconnect driving cables from the basis of an electric motor of the fan and the panel of switches of management of functioning of a heater.

4. Release a reflector of lamps of illumination from a forward part of the panel of switches of management.
5. Release clamps and remove assembly of the switch of the choice of the high-speed modes of the fan from the panel.

6. Installation is made upside-down. The description of the procedure of installation of assembly of a casing of the heater/fan is provided in the Head of the Cooling system, heating.