Skoda Felicia

1. Disconnect a negative wire from the battery.
2. Remove the corresponding front seat (see the Section Removal and installation of seats).
3. Having hooked, remove a decorative cover from the top anchor of a seat belt, then turn out an anchor bolt and disconnect a belt from height regulator.

4. Turn out the screw of fastening of the top panel of internal finishing of a door pillar, then hook and remove the panel.

5. In case of need turn out fixing bolts (try to remember an order of installation of washers) and remove the mechanism of the regulator of height of provision of an anchor of a seat belt.

6. Having hooked, separate the upper edge of the lower panel of finishing of a door pillar, then separate the panel from a decorative overlay of a threshold and remove it from the car.

7. Turn out the lower anchor bolt of a seat belt (try to remember an order of installation of washers), then release a belt from a threshold and remove the remote plug from an anchor plate.

8. Turn out a bolt of fastening of an inertial drum of the returnable device and remove a seat belt from the car.

1. Perform the procedures described in paragraphs with 1 on 7.

2. Incline assembly of a back seat forward and accurately release the panel of an overlay of a threshold of a back door from the clamps. Having released all clamps, remove the panel from the car. At removal of a seat belt of a driver's seat from the car equipped with the remote drive of unlocking of a door of a back turn out fixing screws and remove the driving lever with the decorative panel - in process of opening of access disconnect a driving cable.

3. Give a nut of fastening of a natyazhitel on a basic hairpin (it will lead to shutdown of the mechanism of a natyazhitel), also turn out the forward fixing screw.

4. Remove an arm from a forward part of a natyazhitel and release it from a support.

5. Remove a clamp(s) of fastening of a cable of a natyazhitel to a body, then give a bolt of fastening of an inertial drum and remove assembly of a seat belt from the car.

1. Remove assembly of a back seat (see the Section Removal and installation of seats).
2. Turn out the lower anchor bolt of fastening of a seat belt to a floor, remove the remote plugs and a washer installed between an anchor plate of a belt and the panel of a floor.

3. Delay the back end of an overlay of a threshold for the purpose of office it from a floor up.

4. Separate the basis of the side panel of finishing of a back seat from the case, then release it from the top support and remove from the car.

5. Release the shelf of the luggage compartment from the support and remove it саля. On the Station wagon models also remove forward section of the shelf.

6. On models where side panels of finishing of a doorway of a back are imposed on the top panels of finishing of back racks, remove an overlay of a threshold and the corresponding side panel of finishing. For fastening of an overlay of a threshold screws, or clamps are used, - the last are released by extraction from them the central sections. The side panel of finishing fastens the only clip.

7. Shoot from a body the sealing film of an aperture of a back door in the district of the region of the top panel of finishing of a door pillar, then remove the back panel from the top part of a doorway of a back.

8. Turn out forward screws of fastening of the top finishing panel.

9. Accurately remove the handle from the lever of an otpuskaniye of clamps of a back of a back seat.

10. On the Station wagon models uncover access the panel of side finishing of the luggage compartment, then turn out fixing screws and remove the panel from the car. Give the screw of fastening of the panel of a back rack.

11. On all models prop up a back door, then slightly raise a clamp and disconnect the corresponding persistent bar from the spherical hinge.

12. Separate the panel of finishing of a back rack from a body and remove it from the car. Release a seat belt guide from the panel, then remove the panel from a belt and take it from the car. At the corresponding complete set, do not forget to disconnect at removal of the panel an electrical wiring from the lamp / a back loudspeaker.

13. Turn out a fixing bolt and remove the top anchor of a seat belt.

14. Give bolts of fastening of an inertial drum of the returnable device and remove assembly of a seat belt from the car.

1. Remove a seat (see the Section Removal and installation of seats).
2. Remove the seatback inclination regulator handle, then give the fixing boat (do not forget about a washer) and remove a regulator wheel.
3. Release a first line of the panel of side finishing from clamps, then liberate the rear edge of the panel and remove the last from the car.
4. Turn out a fixing bolt (do not forget about a washer and the remote plug) and remove a seat belt buckle.