Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
- Repair of the engine
   - Repair without extraction from the car of the petrol engine of 1.3 l
      Description of the main knots and mechanisms
      Check of a condition of conrod and piston group on hearing and measurement of compression pressure in cylinders
      Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
      Removal and installation of a cover of a casing of the camshaft
      Removal, check of a state and installation of assembly of an axis of yokes
      Removal and installation of a head of cylinders assembled with the inlet pipeline and a final collector
      Removal, check of a state and installation of a forward cover, chain and asterisks of the GRM drive
      Removal, check of a state and installation of components of the oil pump
      Removal and installation of the pallet of a case of the engine
      Replacement of epiploons of a bent shaft
      Removal, check of a state and installation of a flywheel
      Check of a state and replacement of rubber pillows of support of a suspension bracket of the power unit
      Removal, installation and adjustment of effort of a tension of a belt of the drive of auxiliary units
   + Repair without extraction from the car of the petrol engine of 1.6 l
   + Repair without extraction from the car of the diesel engine
   + Dismantle of the power unit and capital repairs of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and finishing of salon
+ Onboard electric equipment





Check of a state and replacement of rubber pillows of support of a suspension bracket of the power unit

Detailed information on placement and the device of support of the power unit is provided in the Section Removal from the car of the power unit - preparation and precautionary measures, general information about a suspension bracket of the power unit.

CHECK

 PERFORMANCE ORDER

1. A car front also establish to Poddomkratta it on props.
2. Check pillows of support of a suspension bracket of the power unit for existence of cracks, signs of hardening of material, peelings of rubber from a metal basis of other damages. Defective support are subject to replacement.
3. By means of a dynamometer key check correctness of efforts of tightening of threaded connections of support.
4. Using the big screw-driver or mount as the lever, estimate degree of wear of support (in case of need use the help of the assistant). In case of identification of an excessive side play replace worn-out components, previously having made sure of reliability of tightening of fixture.

REPLACEMENT

Right support

 PERFORMANCE ORDER

The rubber pillow of the right support is built in in the case of the water pump. Extraction of a pillow is made by means of a hydraulic press, or a set of borodok with remote plugs. Performance of this work will be more correct to be charged to experts of a workshop of car service.


Left support


 PERFORMANCE ORDER

The pillow of the left support is built in in a face cover of a case of the transmission and service center of the Skoda company by means of a special stripper can be taken in a workshop company.


Back support


 PERFORMANCE ORDER

1. The lever support of a back suspension bracket is equipped with two rubber torsion inserts, one of which (main) is pressed in the arm fixed on a back wall of a case of RKPP the second, the smaller size the rubber plug, pressed in a back part of the coulisse of a stretcher of a forward suspension bracket. Replacement of rubber components of a support is made in the conditions of a workshop of car service as for its performance special devices are required.

2. For extraction of the main torsion insert prop up the power unit the second jack (for the purpose of distribution of loading lay wooden whetstone between a head of a jack and the pallet of a case). Remove a nut and a through bolt of fastening of a support to the coulisse of a stretcher. Give two bolts and a nut (on models of the last years of release - three nuts) fastenings of a support to a case of the transmission and remove assembly of a support from the car.

3. For removal of the coulisse give a nut of fastening of its back part to a basic arm on a stretcher, take a through bolt with a washer. Then give a nut and take a through bolt of fastening of the coulisse to an arm of the main support. Remove the coulisse and take it from under the car.
4. Installation is carried out upside-down. Track respect for efforts of tightening of fixture.