Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
- Repair of the engine
   - Repair without extraction from the car of the petrol engine of 1.3 l
      Description of the main knots and mechanisms
      Check of a condition of conrod and piston group on hearing and measurement of compression pressure in cylinders
      Reduction of the piston of the first cylinder in the provision of the top dead point (TDP)
      Removal and installation of a cover of a casing of the camshaft
      Removal, check of a state and installation of assembly of an axis of yokes
      Removal and installation of a head of cylinders assembled with the inlet pipeline and a final collector
      Removal, check of a state and installation of a forward cover, chain and asterisks of the GRM drive
      Removal, check of a state and installation of components of the oil pump
      Removal and installation of the pallet of a case of the engine
      Replacement of epiploons of a bent shaft
      Removal, check of a state and installation of a flywheel
      Check of a state and replacement of rubber pillows of support of a suspension bracket of the power unit
      Removal, installation and adjustment of effort of a tension of a belt of the drive of auxiliary units
   + Repair without extraction from the car of the petrol engine of 1.6 l
   + Repair without extraction from the car of the diesel engine
   + Dismantle of the power unit and capital repairs of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and finishing of salon
+ Onboard electric equipment





Replacement of epiploons of a bent shaft

The right epiploon (from a pulley)

 PERFORMANCE ORDER

1. Remove a pulley of a bent shaft (see the Section Removal, check of a state and installation of a forward cover, chain and asterisks of the GRM drive).

2. Having carefully hooked the screw-driver with a flat sting, take an epiploon from a GRM drive chain cover. Try not to damage the condensed surfaces of a cover and a pin of a bent shaft.

3. Alternatively, drill or puncture couple of small openings in a face surface of an epiploon and screw in them self-tapping screws. Now it is possible to take from a cover, having grasped heads of self-tapping screws with flat-nose pliers.
4. Carefully wipe and polish epiploon nest walls, and also a surface of a pin of a bent shaft - from the condensed surfaces any roughnesses, agnails and teases capable to lead to bystry failure of a new epiploon have to be removed.

5. Oil pure motive sponges of a new epiploon, and press/begin to knock the last sponges inside in a nest in a casing aflush with an external surface of a cover of a gas-distributing chain. As a mandrel for landing of an epiploon it is possible to use a face head of the corresponding size or a piece of a pipe of suitable diameter which have to rest only against the rigid outer edge of a face surface of an epiploon.

6. Collect by rags all traces of oil, then establish a pulley of a bent shaft (see the Section Removal, check of a state and installation of a forward cover, chain and asterisks of the GRM drive). Let's notice, when fixing a bent shaft from a provorachivaniye in the course of installation of a pulley it is necessary to remove the case pallet for the purpose of a possibility of control of provision of a persistent washer.


The left epiploon (from a flywheel)


 PERFORMANCE ORDER

1. Remove a flywheel (see the Section Removal, check of a state and installation of a flywheel).

2. Accurately puncture or drill two openings in a face surface of an epiploon and screw in them self-tapping screws. Take an epiploon from the nest in a wall of the block of cylinders, having grasped heads of screws with flat-nose pliers.

3. Carefully wipe and polish epiploon nest walls, and also a surface of a pin of a bent shaft - from the condensed surfaces any roughnesses, agnails and teases capable to lead to bystry failure of a new epiploon have to be removed.
4. Oil pure motive sponges of a new epiploon, and press/begin to knock the last sponges inside in a nest in an engine case.
5. Manually put on a new epiploon a pin of a bent shaft, having accurately translated it through a coat hanger and press it in a nest so that the external end face evenly on all perimeter was pressed a persistent surface of a coat hanger. In case of need the epiploon can be begun to knock in a nest the hammer with soft brisk.
6. Remove the remains of lubricant and establish into place a flywheel (see the Section Removal, check of a state and installation of a flywheel).