Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
- Body and finishing of salon
   General information and precautionary measures
   Care of components of a body and bottom of the car
   Care of an upholstery and carpets of salon
   Repair of insignificant damages of body panels
   Repair of seriously damaged body panels
   Removal and installation of a front bumper
   Removal and installation of a rear bumper
   Removal, installation and adjustment of a cowl
   Removal and installation of a driving cable of an otpuskaniye of the lock of a cowl
   Removal, installation and adjustment of assembly of the lock of a cowl
   Removal and installation of doors
   Removal and installation of panels of an internal upholstery of doors
   Removal and installation of door handles and components of the lock
   Removal and installation of door glasses and regulators of window regulators
   Removal and installation of a door of a back and its persistent bars
   Removal, installation and adjustment of components of the lock of a door of a back
   Removal and installation of components of the uniform lock
   Removal and installation of components of the electric drive of window regulators
   Removal and installation of external rear-view mirrors and the accompanying components
   Windshield and glass of a door of a back - the general information
   Top hatch
   Removal and installation of elements of body finishing
   Removal and installation of seats
   The mechanism of a natyazhitel of a seat belt of a front seat - the general information
   Removal and installation of components of seat belts
   Removal and installation of elements of finishing of salon
   Removal and installation of the central console
   Removal and installation of the dashboard
   Control body sizes
+ Onboard electric equipment



Removal and installation of doors

REMOVAL

 PERFORMANCE ORDER

1. Disconnect a negative wire from the battery.

2. If the door is equipped with electric components, remove from it the panel of an internal upholstery (see the Section Removal and installation of panels of an internal upholstery of doors). Accurately separate an insulating film from door inside, then disunite sockets release an electrical wiring from intermediate clamps...

... release a rubber protective cover from a forward face wall of a door, then take an electrical wiring from a frame.

3. Give a nut of an axial bolt of fastening to an opening limiter door. Take a bolt. Further act according to the instructions provided in the corresponding subsection.


Forward door

 PERFORMANCE ORDER

1. Ask the assistant to take a door, then by means of the hammer and a suitable drift beat out loopy fingers. Try not to bend fingers in the course of their extraction from loops. Otherwise at assembly they will need to be replaced.

2. Having taken out fingers of both loops, remove a door from the car.

3. Check loops for existence of signs of wear and mechanical damages. In need of replacement mark the provision of a loopy level on a rack, then turn out a fixing bolt and remove a loop together with adjusting washer(s) (if those are established). Replace a defective loop together with washer(s) and achieve alignment of its provision of the tags which are rather put in the course of dismantle. Screw a fixing bolt and tighten it with the required effort.


Back door

 PERFORMANCE ORDER

1. A marker lead round each of loopy levels on a car body. ask the assistant to take a door and turn out bolts of fastening of loops.

2. Remove a door from the car, then remove the adjusting washers established between loops and a body (if those are provided).
3. Check loops for existence of signs of wear and mechanical damages. In need of replacement accurately beat out loopy fingers. Grease new fingers with universal lubricant, establish loops on a door, then fill in them fingers. Clog with the hammer fingers into loops and make sure of an isprvnost of rotation of the last. Only after it start installation of a door on the car.

INSTALLATION

Forward door

 PERFORMANCE ORDER

1. Grease loopy fingers with universal lubricant, then get a door on the regular place on the car. Establish fingers, having reliably begun to knock them in loops.

2. Level the limiter on the arm, then grease an axial bolt with universal lubricant, fill it in a nest and strongly tighten a nut.
3. At the corresponding complete set fill an electrical wiring in a doorframe and put into place a protective cover. Track correctness of laying of wires and reliability of their fastening in all provided intermediate clamps. Establish into place an insulating film and the panel of an internal upholstery of a door (see the Section Removal and installation of panels of an internal upholstery of doors).
4. Check correctness of installation of a door in a body aperture, in case of need make the corresponding adjustment, then connect a negative wire to the battery.


Back door

 PERFORMANCE ORDER

1. By means of the assistant get a door on the regular place and screw loopy bolts. Between loops and a body establish all provided adjusting washers. Level loops of the tags which are rather put in the course of dismantle, then tighten fixing bolts with the required effort.
2. Perform the procedures described in paragraphs with 2 on 3 subsections Installation.

ADJUSTMENT

 PERFORMANCE ORDER

1. Close a door and check correctness of its placement in a body aperture of rather surrounding panels. Insignificant updating of the provision of a door in an aperture can be executed by selection of the adjusting washers established under loops. Having achieved satisfactory result, tighten bolts of fastening of loops with the required effort.

On forward doors access to loopy bolts can be significantly facilitated due to removal of the limiter of opening of a door.

2. Having finished adjustment, check serviceability of operation of the lock. The drummer has to enter densely the lock and it is reliable to be blocked by a latch. In case of need weaken fixing bolts and correct position of the drummer. Having achieved satisfactory result, tighten fixing screws with the required effort.

1 — Screws
2 — the Drummer