Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment



Removal and installation of the stabilizer of cross stability of a forward suspension bracket

At assembly the new cylindrical pin of a rod of the choice of transfers is required.

REMOVAL

 PERFORMANCE ORDER

1. Prop up wedges back wheels, firmly cock the parking brake, then a front of the car and establish to a poddomkratta it on props. Remove both forward wheels.

2. On the end of a rod of the choice of transfers turned to RKPP remove a fixing collar, having provided access to a cylindrical pin.

ри assembly should replace a collar of a basic equipment more convenient screw or worm. Beat out and will throw out an old cylindrical pin - at assembly it is subject to replacement without fail.

3. Give a nut of an axial bolt of fastening of a rod of the choice of transfers to RKPP control lever basis / to a basic plate. Take an axial bolt and disconnect a rod from an axis of forks of switching in the transmission. Remove a rod from the car. From the basis of a control lever of RKPP take the axial plug (i).
4. Turn out a bolt of fastening of a bar of the mechanism of switching to the transmission. Remove washers and a rubber pillow.
5. Remove both racks of a bar of the stabilizer of cross stability (see the Section Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket).

6. Turn out bolts of fastening of collars of support of a bar to a stretcher. Remove collars.

7. Take a bar of the stabilizer of cross stability from under the car and remove from it rubber plugs of support.
8. Attentively examine stabilizer components on existence of signs of wear, aging of material or mechanical damages. Special attention should be paid to a condition of rubber plugs of support. Replace defective components.

INSTALLATION

 PERFORMANCE ORDER

1. Put on a stabilizer bar rubber plugs of support (the flat parties up).
2. Get a bar of the stabilizer of cross stability on the regular place on a stretcher. Establish collars of fastening of support, having tracked correctness of their gearing in a back part of a stretcher. Screw fixing bolts.
3. Establish racks of a bar of the stabilizer of cross stability (see the Section Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket), then tighten bolts of collars with the required effort.
4. Clean a carving of bolts of fastening of components of the mechanism of gear shifting.
5. Make sure of correctness of landing of rubber plugs and washers, connect a switching mechanism bar to RKPP case. Slightly grease a carving of a fixing bolt with sealant like Loctite 279 or Three Bond 1305, then screw a bolt and tighten it with the required effort (see the Head the Transmission).
6. Make sure of correctness of installation of the axial plug(s) of a control lever of RKPP. Grease the plug (i) with universal lubricant. Establish into place a rod of the choice of transfers, grease with sealant (see the previous paragraph) a nut carving, then screw the last on a bolt and tighten it with the required effort (see the Head the Transmission). By means of a new cylindrical pin connect a choice rod to RKPP. Record a pin a collar of screw or worm type.
7. Establish to the place of a wheel, lower the car on the earth and tighten wheel bolts with the required effort.