Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment


Все про автомобили: https://myavto24.ru

Removal and installation of racks of a forward suspension bracket

At assembly the new nut of a coupling bolt of stupichny assembly, and also new nuts of the top support of a rack will be required.

REMOVAL

 PERFORMANCE ORDER

1. Open a cowl and check a motive compartment for existence of an expansion bar of the top support of racks of a suspension bracket. In case of need, give nuts of the top support and remove a bar.

2. Prop up wedges back wheels, cock the parking brake, then a front of the car and establish to a poddomkratta it on props. Remove the corresponding forward wheel.
3. On the models equipped with the stabilizer of cross stability give a nut of fastening of a rack of a bar of the stabilizer to the lower lever, remove a washer and the lower rubber insert.

4. On all models give a nut and take a coupling bolt of fastening of stupichny assembly to a rack.

At assembly the nut is subject to replacement without fail.

5. By means of mount carefully lower the lower lever, releasing a spherical support from the landing collar in the basis of stupichny assembly, - try not to allow an excessive tension of a brake hose. If assembly does not separate from a rack, accurately part with the big screw-driver with a flat sting sponges of a fixing collar. On the models equipped with the stabilizer of cross stability try not to allow losses of a rubber pillow and a washer of the top support of a rack of a bar of the stabilizer.

The coupling bolt of a spherical support is subject to replacement without fail (in a set with the nut).

6. In a motive compartment remove a plastic cover, then give nuts of the top support of a rack and remove washers.

At assembly of a nut are subject to replacement without fail. Take a rack through an arch of a wheel and remove it from the car.

INSTALLATION

 PERFORMANCE ORDER

1. Through an arch of a wheel get a rack on the regular place, establish washers and screw new top nuts. Tighten nuts with the required effort, then establish a plastic cover. If the car is equipped with an expansion bar, temporarily screw old nuts, having only slightly tightened them.
2. Enter the lower part of a rack into gearing with stupichny assembly. On the models equipped with the stabilizer of cross stability place a stabilizer bar rack on the lower lever of a suspension bracket, having tracked correctness of an arrangement of the top rubber insert and washer.
3. Achieve combination of fixing openings, insert a coupling bolt, screw a new nut and tighten it with the required effort.
4. Where it is required, establish the lower rubber insert and a washer of a support of a rack of a bar of the stabilizer. Screw a nut and tighten it with the required effort.
5. Establish into place a wheel, then lower the car on the earth and tighten wheel bolts with the required effort.

6. On the models equipped with an expansion bar of racks remove old nuts of fastening of a bar and replace them new (do not forget to enclose washers), having tightened them with the required effort.