Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
- Routine maintenance
   Weekly checks
   - Routine maintenance of the car - petrol models
      Schedule of routine maintenance
      Regular service
      Replacement of motive oil and oil filter
      Check of a condition of blocks and disks of forward brake mechanisms
      Check of serviceability of functioning of a control system of the engine
      Check and adjustment of valvate gaps (model of 1.3 l)
      Check of a condition of hoses, and identification of sources of leaks
      Check of a condition of protective covers of power shafts
      Suspension bracket and drive of steering
      Check of a condition of components of system of production of the fulfilled gases
      Check of a condition of cooling liquid
      Check of serviceability of functioning of coupling
      Greasing of locks and loops
      Check of composition of the fulfilled gases
      Adjustment of an optical axis of head headlights
      Check of serviceability of functioning of cleaners/washers of glasses/lenses of head headlights
      Trial runs
      Replacement of the filtering air cleaner element
      Replacement of spark plugs - models of 1.3 l
      Check of a condition of a belt of the GRM drive - model of 1.6 l
      Greasing of the distributor of ignition - model of 1.3 l
      Check of a condition of a belt of the drive of auxiliary units
      Check of system of safety cushions
      Check of serviceability of functioning of systems of decrease in toxicity of the fulfilled engine gases
      Check of a condition of boots and drums of back brake mechanisms
      Check of serviceability of functioning of the parking brake
      Check of body panels on existence of traces of development of corrosion
      Check of level of gearbox oil
      Replacement of spark plugs - models of 1.6 l
      Replacement of the fuel filter
      Replacement of gearbox oil
      Replacement of a gas-distributing belt - model of 1.6 l
      Replacement of brake fluid
      Replacement of cooling liquid
   + Routine maintenance of the car - diesel models
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body and finishing of salon
+ Onboard electric equipment



Suspension bracket and drive of steering

Forward suspension bracket and steering drive

 PERFORMANCE ORDER

1. A car front also establish to Poddomkratta it on props.

2. Make visual check of a condition of boots of spherical support and protective covers of a case of a steering rack. Replace the covers which are worn out or allowing leaks - hit in boots of dirt or moisture leads to acceleration of wear of spherical support and components of rack transfer.

3. On models, the equipped system of hydrostrengthening of a wheel, check a condition of hoses of PAS. Examine nipple connections of hydraulic lines and covers of a case of the steering mechanism on existence of signs of leaks. Dribble of oil through protective covers at increase in pressure in a case of a steering rack usually testifies to wear of epiploons.

4. Grasp a forward wheel of the car in points on 12 and for 6 hours and sharply pull it. Existence of the slightest noticeable side play demands conducting investigation of the reasons of its emergence. Continuing to pull a wheel, ask the assistant to squeeze out a pedal of a foot brake. If the side play at the same time disappears or will considerably be reduced, therefore wear of stupichny bearings takes place. Otherwise it is necessary to check a condition of hinges and support of components of a suspension bracket.

5. Now grasp a wheel in points on 9 and for 3 hours and repeat check. The side play besides can be connected with wear of stupichny bearings. Wear of tips of steering drafts is the second possible reason of a weak point. At wear of external tips the visual side play of a wheel usually takes place. For assessment of degree of wear of the hinge of an internal tip put a hand on a protective cover of a case of rack transfer, grasp with the second hand draft. If now to pull a wheel, it will be possible to feel a side play in the worn-out hinge.
6. By means of mount or the big screw-driver estimate degree of wear of plugs of support of a suspension bracket: you start the lever between the corresponding component and its reference point. Existence of a small side play is quite natural and is explained by elasticity of rubber inserts, however the excessive weak point testifies to wear of a support. In parallel, visually estimate a condition of all rubber pillows and inserts opened to access. Pay attention to such defects as cracks, stratifications, gaps, material aging signs, etc.
7. Lower the car on the earth and ask the assistant to rotate a steering wheel approximately on 1/8 turns in each of the parties. The delay in response of the operated wheels to rotation of a steering wheel (side play) has to be very small, and ideally be absent at all. Otherwise check a condition of hinges and support of components of a suspension bracket and the steering drive. Estimate degree of wear of cardan hinges of a steering column, and also components of actually rack transfer.


Back suspension bracket

 PERFORMANCE ORDER

1. Prop up wedges forward wheels, then a back of the car and establish to a poddomkratta it on props.
2. Working as above for a forward suspension bracket is described, estimate degree of wear of stupichny bearings, suspension bracket plugs, and at the corresponding complete set - support of rack-mount shock-absorbers.


Racks of a suspension bracket and shock-absorbers

 PERFORMANCE ORDER

1. Check shock-absorbers for existence of traces of leak of hydraulic liquid on the case, a rubber boot and through a piston rod. Leaks testify to internal defect of the shock-absorber and need of carrying out replacement.

Replacement of rack-mount assemblies / shock-absorbers is always made in couple for this bridge of a suspension bracket.

2. Efficiency of action of rack-mount assemblies can be checked by a serial nazhimaniye for each of car corners. At a corner otpuskaniye the body has to come back to a starting position without rocking. Otherwise the corresponding shock-absorber needs more detailed attention. Do not forget to estimate also degree of wear of components of the top and lower support of shock-absorbers.