Skoda Felicia

1. In case of need give nuts of fastening of the top support of racks of a suspension bracket and remove a rack-mount strut from the car.

2. Working according to the instructions provided in the corresponding Part of the Head the Power supply system, perform the following procedures: a) On petrol models of 1.3 l of SPFI remove assembly of the air cleaner; b) On petrol models of 1.3 l of MPFI to an otboltita also remove assembly of the case of a throttle from the inlet pipeline. Take assembly aside, without disconnecting an accelerator cable, an electrical wiring and connecting hoses; c) On petrol models of 1.6 l remove a sleeve of an inlet air inlet; d) On diesel models remove the top section of the inlet pipeline.

3. Release clamps of fastening of an air inlet to the top part of a casing of a heater...

... take an air inlet from a motive compartment.

4. Remove the battery (see the Head Elektrooborudovaniye of the engine).
5. Remove an instrument guard and the lighter (see the Head Onboard electric equipment).
6. Find and disunite the electric socket of the control panel of system of heating/ventilation of salon on the left side of a casing.

If access to the socket is limited, its rassoyedineniye can be made after removal of a casing.

7. Through an opening under installation of the lighter release a clamp of fastening of a sleeve of air supply in a foot well to the heater casing basis.

8. In a motive compartment press hoses of a heating path for the purpose of minimization of losses of cooling liquid. Enclose rags under heater heat exchanger unions, then release collars and disconnect both hoses. At once wash away the spilled cooling liquid water. Impose a casing of a heater with rags.

9. Give nuts of fastening of assembly of a casing of a heater to a partition of a motive compartment.

10. Ask the assistant to make sure that the control panel of system is released from the dashboard, then lift assembly of a casing with the control panel and remove it from the car,

... in process of ensuring access having disconnected the socket of an electrical wiring Lay assembly by unions for the purpose of minimization of losses of cooling liquid up.

11. Installation is made upside-down. Special attention should be paid to the next moments:

a) Before installation check a condition of pereborochny laying, in case of need make its replacement;
b) Track correctness of landing of assembly of a casing and reliability of fastening of air ducts and branch pipes, only after it start tightening of fixing nuts;
c) Track reliability of fastening on unions of the heat exchanger of the corresponding hoses;
d) In conclusion add necessary amount of mix of the required structure in the cooling system.

1. Remove assembly of a casing of a heater with the control panel.

2. Try to remember the adjusting provision of each of driving cables (tips of cables have color marking). Then, by means of flat-nose pliers release fixing clips and disconnect cables from the panel.

3. Disconnect an electrical wiring from the driving motor of the fan of a heater, then separate the panel from a casing.

4. Assembly is carried out upside-down. Track correctness of laying and reliability of fastening on the regular places of all driving cables. A feather final installation of assembly of a casing check serviceability of functioning of switches of management for the car.

1. Release fixing and remove an air inlet from a heater casing.

2. For the purpose of ensuring access remove the battery.

3. Walk on an electrical wiring from an electric motor the heater fan truth to the socket. Disunite the socket...

also release the rubber plug of a plait through passage from a casing, then extend a plait from a casing.

4. Turn out fixing screws, release clamps and remove assembly of a basic plate of an electric motor of the fan from a heater casing.

5. Releasing from clamps, uncover,

then weaken the screw

also separate the motor from a plate.

6. Assembly is made upside-down. In conclusion do not forget to install into place the battery and to check freedom of rotation of a krylchatka of the fan of a heater.

1. For the purpose of ensuring access remove the battery.
2. Release clamps and remove an air inlet from a heater casing.
3. Disunite the fan electrical wiring socket.

4. Give fixing nuts and remove assembly of a basic plate of an electric motor from a heater casing.

5. For the purpose of ensuring access to the motor, release clamps and uncover. Turn out a coupling bolt and remove the motor from a basic plate.
6. Installation is made upside-down. In conclusion install into place the battery and check freedom of rotation of a krylchatka.

1. The resistor is in a motive compartment and is fixed on the right wall of assembly of a casing of a heater. On models with left-side steering for ensuring access to the resistor it is necessary to remove the battery.
2. Disunite the electric socket, then release the resistor from clamps and remove it from a casing.

3. Installation is made upside-down. Track reliability of fastening of the resistor.

1. The resistor is in a motive compartment and is fixed on the left wall of assembly of a casing of a heater. For ensuring access to the resistor it is necessary to remove the battery.
2. Disunite electric sockets. Try to remember an order of their connection.
3. Turn out fixing screws and remove the resistor from a casing.
4. Installation is made upside-down.

1. Remove a heater casing.

2. Turn out the fixing screw and take the heat exchanger from a casing. Try not to wound fingers about keen edges of plates of the heat exchanger!

3. Before installation check a condition of sealing foam mass of the heat exchanger. Accurately start assembly on the regular place in a casing and strongly tighten the fixing screw. Then establish into place a casing.

1. On models with left-side steering remove the battery.
2. On all models in a motive compartment press clamps the hoses going to the heater heat exchanger. Enclose rags under unions, then release collars and disconnect both hoses. Collect traces of the spilled liquid, impose with rags a heater casing.

3. Release clamping bolts and disconnect driving cables from draft of the thermostat of the heat exchanger. Release a clip and disconnect a cover of the top cable, then give the top and lower fixing nuts and remove the executive lever of the gate from a casing. 1 — the Fixing nut 2 — the Driving cable 3 — the Driving cable 4 — a cable Guide 5 — the Executive lever 6 — Clamping a bolt 7 — the Cable 8 — Clamping a bolt

4. Accurately releasing from clamps, remove the top part of a cover of the heat exchanger from a heater casing.
5. Carefully take the heat exchanger.

Do not cut fingers about keen edges of plates!

6. Installation is made upside-down. Do not forget to check a condition of sealing weight.

1. In a motive compartment remove clamps and remove the thermofilter from a heater casing.
2. Find and disunite the fan motor electrical wiring socket in a forward part of a casing. Push the rubber plug through passage in a casing.
3. Disconnect a vacuum hose from diaphragm assembly of the inlet gate. Also disconnect a rod from draft of a diaphragm.
4. Turn out fixing screws, release collars and, releasing an electrical wiring, remove an air inlet from the top part of a casing of a heater.
5. Turn out fixing screws and remove assembly of a driving electric motor.
6. Installation is made upside-down. Track correctness of landing of the plug through passage of an electrical wiring. Century the conclusion check serviceability of functioning of the gate of an air inlet.

1 The resistor is located in a motive compartment on the left wall of a casing of a heater. For the purpose of ensuring access to the resistor remove the battery.
2 Disunite the electric socket, release the resistor from clamps and remove it from a casing.
3 Installation is made upside-down. Track reliability of fastening of the resistor on a casing.

Performing procedures of removal and installation of the heat exchanger should be charged to specialists of car service in view of need of a detachment of refrigerator lines from the broad valve of the evaporator (see the Section Air conditioning system - the general information and precautionary measures).