Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment



Replacement of bearings of forward wheels

Assembly of a nave of a forward wheel

1 — the Rotary fist
2 — the Bearing
3 — the Spring ring
4 — the Nave

5 — the Nut
6 — the Spherical support
7 — the Brake disk


The two-row roller wheel bearing has tight execution. Assembly stuffing and installation of a pretightness are made by lubricant at manufacturer of the car. The bearing is calculated on all service life of the car and does not need in any additional service. Try not to allow tightenings of a stupichny nut with excessive effort, - use a dynamometer key.


Performing procedures of dismantling and assembly of the wheel bearing will require a suitable press in which lack a big verstachny vice with a set of cylindrical mandrels will fit (as those the face heads suitable by the size perfectly will approach). Internal holders of the bearing внатяг are put on a nave. If at dismantle of the bearing the holder remained on a nave, its removal requires a special stripper with captures of lezviyny type.

 PERFORMANCE ORDER

1. Remove stupichny assembly from the car (see the Section Removal and installation of stupichny assemblies of forward wheels).

2. Strongly lay assembly on pair of wooden blocks, or clamp it in a vice with soft sponges. By means of the cylindrical mandrel leaning only in an inner edge of a stupichny flange squeeze out the last of the bearing. If an external part of an internal holder of the bearing remains on a nave, use a stripper.

3. Remove a lock ring from the external end of stupichny assembly.

4. Strongly prop up the outer side of stupichny assembly. By means of the cylindrical mandrel leaning only in an internal holder of the bearing squeeze out assembly of the last of a nave.

5. Carefully clear stupichny assembly of dirt and traces of lubricant. Remove with an emery paper agnails and the teases capable to interfere with assembly of components. Check components for existence of cracks and other signs of wear. Replace defective parts.
6. For the purpose of simplification of assembly of components slightly grease an external holder of the bearing and a pin of a flange of a nave with oil like Optimol VP317.

7. Strongly prop up a nave and fill in it the bearing. By means of the cylindrical mandrel resting only against an external holder of the bearing press the last against the stop in a nest in a nave. Make sure of perpendicularity of landing of the bearing.

8. Having put the bearing in a nave, fix it a lock ring. Track correctness of landing of a ring in the flute.
9. Strongly prop up the outer side of a flange of stupichny assembly Put on an internal holder of the bearing the end of a flange. By means of the cylindrical mandrel resting only against an internal holder put the bearing against the stop in an assembly coat hanger. Check freedom of rotation of a flange, remove excess of oil/lubricant.
10. Install stupichny assembly on the car (see the Section Removal and installation of stupichny assemblies of forward wheels).