Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment



Removal and installation of the steering pump

REMOVAL

 PERFORMANCE ORDER

1. Firmly cock the parking brake, then a front of the car and establish to a poddomkratta it on props.
2. Release bolts of fastening of a pulley of a driving belt to the steering pump, then weaken a belt and throw off it from a pulley. Now turn out fixing bolts and remove a pulley from the pump, having tried to remember its adjusting situation.
3. Special clips or clamps press the giving and feeding hoses near the tank of the steering pump for the purpose of minimization of losses of hydraulic liquid.
4. Turn out the fixing screw and remove a collar of fastening of the giving tube from a basic arm (if that is provided).

5. Release a collar and disconnect the giving hose from the pump, then turn out a nipple bolt and disconnect the feeding hose. For collecting the spilled liquid prepare drain capacity. The open ends of hoses/tubes at once to a zakuporta for the purpose of minimization of losses of liquid and in order to avoid hit in hydraulic system of dirt. Remove sealing washers of nipple connection of a hydraulic tube.

At assembly sealing washers are subject to replacement without fail.

6. Turn out bolts of fastening of the pump and take the last from an assembly bracket.
7. The pump is executed in a look to tight assembly and recovery repair is not subject. In case of refusal make replacement.

INSTALLATION

 PERFORMANCE ORDER

1. Start the pump on the regular place, screw fixing bolts and tighten them with the required effort.
2. Establish new sealing washers on both sides of nipple connection of the feeding tube, then screw a nipple bolt. Make sure of correctness of joining of the socket and strongly tighten a nipple bolt.
3. Connect the giving tube to the pump, having reliably fixed it by a collar. Now the clips pressing hoses can be removed.
4. Install the steering pump on basic arms, screw fixing bolts and tighten them with the required effort.
5. Establish into place a pump pulley while only slightly having tightened fixing bolts. Make adjustment of a natyazhiyeniye of a belt, then finally tighten bolts of fastening of a pulley.
6. In conclusion "pump over" hydraulic system (see the Section Removal of Air Traffic Jams from a hydraulic path of system of strengthening of a wheel).