Skoda Felicia

since 1994 release

Repair and operation of the car



Skoda Felicia
+ Cars of the Skoda Felicia brand
+ Maintenance instruction
+ Routine maintenance
+ Repair of the engine
+ Cooling systems, heating
+ Power supply system
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   General information and precautionary measures
   Removal and installation of stupichny assemblies of forward wheels
   Replacement of bearings of forward wheels
   Removal and installation of racks of a forward suspension bracket
   Capital repairs of racks of a forward suspension bracket
   Removal, capital repairs and installation of the lower levers of a forward suspension bracket
   Replacement of spherical support of the lower levers of a forward suspension bracket
   Removal and installation of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket
   Removal and installation of a forward stretcher
   Replacement of bearings of back naves
   Removal, capital repairs and installation of racks of a back suspension bracket
   Capital repairs of racks of a back suspension bracket
   Removal, capital repairs and installation of pins of the back bridge
   Removal and installation of the back stabilizer of cross stability
   Removal and installation of the back bridge
   Removal and installation of a steering wheel
   Removal and installation of a steering column
   Capital repairs of a steering column
   Removal and installation of assembly of the lock of ignition/blocking of a wheel
   Removal, capital repairs and installation of the steering mechanism
   Replacement of rubber protective covers of a case of the steering mechanism
   Removal of air traffic jams from a hydraulic path of system of strengthening of a wheel
   Removal and installation of the steering pump
   Removal and installation of external tips of steering drafts
   Removal and installation of steering draft
   The angles of installation of wheels of the car - the general information
+ Body and finishing of salon
+ Onboard electric equipment



Removal and installation of stupichny assemblies of forward wheels

At assembly the new stupichny nut, a nut of a coupling bolt of a spherical support and a nut of a coupling bolt of stupichny assembly will be necessary.

REMOVAL

 PERFORMANCE ORDER

1. Take off a decorative cap of a wheel disk / nave, then weaken a nut of a power shaft and bolts of fastening of a wheel.
2. Prop up wedges back wheels, cock the parking brake, then a front of the car and establish to a poddomkratta it on props. Remove the corresponding forward wheel.
3. On the models equipped with ABS you otboltit the wheel sensor and, without disconnecting an electrical wiring, take him aside from stupichny assembly (see the Head Snyatiye and installation of racks of a bar of the stabilizer of cross stability of a forward suspension bracket).

4. Give a stupichny nut and remove washers. If forgot to weaken a nut while the car stood on the earth, screw in a nave couple (at least) of bolts of fastening of a wheel and strongly tighten them, then ask the assistant to squeeze out firmly a pedal of a foot brake for the purpose of blocking of a nave from a provorachivaniye and give a nut.

At assembly the stupichny nut is subject to replacement without fail.

5. Take the forelock and give a nut of fastening of a tip of steering draft on the rotary lever of stupichny assembly. By means of a stripper of spherical support release a tip from the lever.

6. If you are going to dismantle stupichny bearings, remove a brake disk, otherwise screw two bolts of fastening to a nave of assembly of a support with an anchor bracket and remove assembly from a brake disk. Tie up a support a wire to a suspension bracket spring, - try not to allow an excessive tension of a flexible brake hose.

7. On the models equipped with the stabilizer of cross stability give a nut of fastening of a rack of a bar of the stabilizer to the lower lever of a suspension bracket, remove a washer and take a rubber insert.

8. On all models give a nut and take a coupling bolt of a spherical support of the lower lever of a suspension bracket from the basis of stupichny assembly. By means of mount carefully lower the lower lever, releasing a spherical support from the landing collar in stupichny assembly. On the models equipped with the stabilizer of cross stability try not to allow losses of a rubber pillow and a washer of the top support of a rack of a bar of the stabilizer.

The coupling bolt of a spherical support is subject to replacement without fail (in a set with the nut).

9. Give a nut and take a coupling bolt of fastening of stupichny assembly to a suspension bracket rack.

The nut of a coupling bolt is subject to replacement without fail.

10. Separate stupichny assembly from a suspension bracket rack, then remove it from the pin of the external CV JOINT of a power shaft equipped with vents and take from under the car. If assembly does not separate from a rack, accurately part with the big screw-driver with a flat sting sponges of a fixing collar. At too hard landing of a rack on a pin of a shaft bring down her the hammer with soft brisk.

INSTALLATION

 PERFORMANCE ORDER

1. Carefully clear landing vents of a nave and a pin of the external CV JOINT of a power shaft. Against the stop put stupichny assembly on a shaft pin, establish a washer, then screw a new stupichny nut. Slightly tighten a nut.
2. Put stupichny assembly on a suspension bracket rack, having brought an ear of the last to a collar groove. Achieve combination of openings, then insert a coupling bolt, screw a new nut and tighten it with the required effort.
3. Achieve the correct placement of a shaft of a spherical support of the lower lever with a collar of stupichny assembly, insert a coupling bolt, screw a new nut and tighten it with the required effort. On the models equipped with the stabilizer of cross stability place a stabilizer bar rack on the lower lever of a suspension bracket, having tracked correctness of an arrangement of a rubber insert and washer of the top support.
4. Where it is required establish a rubber insert and a washer of the lower support on a stabilizer bar, screw fixing to a hook and tighten it with the required effort.
5. Correctly bring a shaft of the spherical hinge of a tip of steering draft to a landing nest in stupichny assemblies and strongly tighten its fixing nut. Record a nut the new forelock.
6. Where it is required establish on a nave a brake disk (see the Head the Brake system). Put into place assembly of a support with an anchor bracket, - track correctness of landing on both sides of a disk of brake shoes. Tighten with the required effort bolts of fastening of an anchor bracket (see the Head the Brake system).
7. On models with ABS install into place the wheel sensor (see the Head the Brake system).
8. Establish into place a wheel, then lower the car on the earth and tighten nuts of fastening of a wheel with the required effort.
9. Finally tighten a stupichny nut with the required effort, then establish into place a decorative cap of a disk/nave.